EasySens » EasySens
EasySens – as simple as a smile
wireless – no batteries – interoperable
Innovative wireless solar technology enables the harvesting of ambient light sources for temperature and fan control in buildings.
Time-consuming installation works such as wiring or cabling including chiselling become unnecessary. Low material costs and time saving enable reasonable priced system solutions.
EasySens offers significantly more flexibility with regard to the sensor location. Thus, a variable room layout in modern buildings does not present any problems at all.
Even in heritage protected buildings in which no architectural changes are allowed, the integration of sensors for the air-conditioning technology can be easily enabled.
The EasySens system uses a fixed data frame according to the EnOcean standard. Thus, it is guaranteed that the wireless sensors and
receivers by Thermokon can be combined with devices of other manufacturers without any problems.
There are different devices for temperature monitoring, relative humidity, light, set point adjustment and status detection.
Among others, the receivers are available with LON-, EIB-, BACnet- or RS485-interface and are designed as gateways for superior control systems. Connection to other bus systems are feasible without any problems.
Advantages at a Glance:
- No batteries, thus almost maintenance-free
- Easy installation, no wiring
- Flexibility with modernisations
- Direct mounting at representative measuring points
- Cost-effective system solutions
- Safe radio transmission in 868MHz-frequency range
- 315MHz also available
- Minimal transmitting power (10mW) with safe transmission
- Transmitting range up to 30m in buildings and up to 300m in free field
- Saving of environment and resources
- Interoperable
Light + Motion » Light + Motion » MDS – Ceiling Multi Sensor
MDS – Ceiling Multi Sensor
The ceiling multi sensor MDS is designed for motion and light detection in room and office spaces. The measured quantity can be used for a fixed light control by means of downstreamed dimming resistances.
Due to the flat construction, the device is specially suitable for an inconspicuous installation in ceilings. Depending on the type, the MDS offers different output interfaces for coupling to a building control system.
MDS Standard 1
Motion: PIR motion sensor 360° with relay output
Light: Active light sensor 0-10V
MDS Standard 2
Motion: PIR motion sensor 360° with relay output
Light: Active light sensor 0-10V
Temperature: Active temperature sensor 0-10V
MDS LON 1
Motion: PIR motion sensor 360° via LON
Light: Light sensor via LON
MDS LON 2
Motion: PIR motion sensor 360° via LON
Light: Light sensor via LON
Temperature: Temperature sensor via LON
LON interface
FTT10A
Analog output
0-10V, Last max. 10mA
Relay output
Make contact, max. 24V/1A
Motion sensor
4-element PIR (passive infrared),
with status LED for motion detection
Light sensor
0...1kLux, photo diode incl. green filter, accuracy typ. ±50Lux
Temperature
Measuring range 0°C...50°C
Power supply
15-24V DC (±10%) or 24V AC (±10%)
Notice
Optional enclosure for surface-mounting
Ausführliches Produktblatt
Informationen zu den herstellerspezifischen Konfigurationsparametern und Netzwerkvariablen UNVTs und UCTPs
Room Operating Pannels » Room Operating Panels
Room Operating Panels
Our room operating panels are designed for temperature detection and integrated operation of HVAC, lighting and blinds for single room control. Thanks to the high-graded optics and a variety of different designs these products are ideal for design-oriented applications.
Humidity » Humidity » F(T)W04 – Room Humidity Sensor
F(T)W04 – Room Humidity Sensor
Room humidity sensor for measuring relative humidity (type FW04) or humidity and temperature (type FTW04) in room and office spaces etc. Designed for connection to control and display systems.
FW04 A 4-20mA
FW04 V 0-10V
FTW04 AA 2x 4-20mA
FTW04 VV 2x 0-10V
FTW04 AS 4-20mA (humidity), resistor (temperature)
FTW04 VS 0-10V (humidity), resistor (temperature)
Measuring range
Humidity: 0...100% rH
Temperature active: 0°C...+50°C
Temperature passive: depending on sensor used
Accuracy humidity
±2% between 10...90% rH
Power supply
A/AA/AS: 15-24V DC (±10%)
V/VV/VS: 15-24V DC (±10%) or 24V AC (±10%)
Ausführliches Produktblatt
Mixed Gas + CO2 » Mixed Gas + CO2
Mixed Gas + CO2
Mixed gas and CO2 sensors enable an individual and demand-responsive control of outdoor air supply and thus an optimization of the energy consumption. In modern buildings, the use of sensors is almost a matter of course – because energy-saving and well-being of people is of paramount importance.
Pressure » Pressure
Pressure
Pressure sensors installed in air-conditioning and cooling systems have to withstand extreme conditions. Thus, tailor made pressure sensors resisting hardest applications are the solution.
Power-Thyristors » Power Thyristors
Power Thyristors
Applications for power thyristors can more and more be found where ohmic and inductive loads must be controlled (e.g. in industrial furnaces, plastics processing etc.). By means of the modular and compact construction and control with a continuous control signal power thyristors become the perfect actuators for industrial power control.
In-/Output Modules LON » In-/Output Modules LON
In-/Output Modules LON
In-/output modules are designed for status monitoring of floating contacts and control of actuators via relay contacts. By a corresponding software applications they are also suitable for control of lighting and blinds as well as inquiries of window contacts and fire flaps.