德国Beluk GmbH PF-correction/measuring校正测量PCF-relays
Power Factor Control Relay BLR-CX
Microprocessor controlled power factor controller with 1-phase measurement system
zoom |
- Start menu for easy commissioning
- Automatic detection and correction of the phase of current and voltage connection
- Fully-automatic c/k-value setting, self adapting, connection of different capacitor step sizes possible
- Automatic detection and usage of the optimum capacitor step
- Switching programs: Best Fit, LIFO, manual mode, combifilter, progressive
- Capable for 4-quadrant operation
- 1-phase measurement system also suitable for non-sinusodial currents and voltages
- Supply voltage taken from measuring voltage
- Voltage measuring 90 – 550V, 45 – 65Hz
- Current measuring 15mA – 5A, suitable for CT x/1A und x/5A
- Connection with plugable screw terminals
- LCD with backlit
- Display of all important grid and system parameters
- Display of THD U and voltage harmonics from 3rd to 15th order
- Input for temperature sensor or thermostate (n/o)
(this input can be used to switch-over the tarif by n/o contact)
- Alarm relay with voltfree n/o contact (operated at normal function)
- TTL-interface on rear
- Instrument casing for cutout 144 x 144mm, depth 49mm
- Protection class IP20 (casing), IP50 (front)
further information, optional parts and supplies (PDF; 120kb) |
|
Power Factor Control Relay BLR-CM
Mikroprocessor controlled power factor controller with 1-phase measurement system and display of measurement values
zoom |
- Full-automatic c/k-value setting, self adapting (not possible for dynamic steps), connection of different capacitor step sizes possible
- Automatic detection and usage of the optimum capacitor step
- Manual mode possible
- Multiple connection types possible through adjustable phase compensation angle
- Capable for 4-quadrant operating
- Individually configurable discharging time allows quicker switching time
- 1-phase measurement system also suitable for non-sinusodial currents and voltages
- Graphical LCD for display of step status, measurement values and system data
- Measurement display for U, I, P, Q, S, THD U, THD I, ΔQ, F, T
- Harmonics measurement for voltage and current up to the 31. order
- Counter for active and reactive work
- Flexible alarm system with up to 15 alarms
- Programmable digital input and digital output
- Programmable alarm relay with voltfree c/o contact
- Supply voltage 115/230V, 45-65Hz, other voltages on request
- Voltage measuring 50 – 530V, 45 – 65Hz
- Current measuring 15mA – 5A, suitable for CT x/1A und x/5A
- Connecting with pluggable screw terminals
- Instrument casing for cutout 144 x 144mm, depth 49mm
- Protection class IP20 (casinge), IP50 (front)
further information, optional parts and supplies (PDF; 110kb) |
|
Power Factor Control Relay BLR-CM 3-phase
Microprocessor controlled power factor controlled with 3-phase measurement system and display of measurement values
zoom |
- Full-automatic c/k-value setting, self adapting, connection of different capacitor step sizes possible
- Capacitors and detected or programmed with values in all three phases. This allows using single-phase or three-phase capacitors in any sequence
- Automatic detection and usage of the optimum capacitor step
- Manual mode possible
- multiple connecting types possible through adjustable phase compensation angle
- Capable for 4-quadrant operation
- Individually configurable discharging time allows quicker switching time
- 3-phase measurement system also suitable for non-sinusodial currents and voltages
- Graphical LCD for display of step status, measurement values and system data
- Measurement display for U, I, P, Q, S, THD U, THD I, ΔQ, F, T
- Harmonic measurement for voltage and current up to the 31. order
- Counter for active and reactive work
- Flexible alarm system with up to 15 alarms
- Programmable digital input and digital output
- Programmable alarm relay with voltfree c/o contact
- Supply voltage 115/230V, 45-65Hz, andere Spannungen auf Anfrage
- Voltage measuring 50 – 530V, 45 – 65Hz
- Current measuring 3 x 15mA – 5A, suitable for CT x/1A und x/5A
- Connection with pluggable screw terminials
- Instument casing for cutout 144 x 144mm, depth 49mm
- Protection class IP20 (casing), IP50 (front)
further information, options and supplies (PDF; 170kb) |
thyristor-switches
Static Contactor BEL-TS
Thyristor switch for rapid switching of capacitors in LV-grid
zoom |
- Switching without inrush current, smooth disconnecting
- Rapid switching
- Can be used in chocked capacitor banks and unchocked as well
- Depending on the type for max. voltage 525V or 690V
- Recovery time 20ms
- Voltage level trigger signal 8 - 30V DC
- Protection class IP00
further information, optional parts and supplies (PDF; 220kb) |
monitoring relays
Capacitor Protection Relay KSR
Multi-function capacitor protecting relay for unbalanced supervision of 3-phase capacitor banks in doublestar connection (current unbalance supervision)
zoom |
- User guidance with plain text menu
- Measurement data displayed on large LCD display with backlight
- Harmonics measurement up to the 63. harmonic for voltage and current
- Connected to voltage tranformers also suitable for higher voltages
- Integration in networks possible via interface RS485 Modbus RTU (optional)
- Flexible alarm system enables supervision of up to 32 measurement values
- Output relays can be programmed for external alarm
- Voltage measuring mains: 50 – 530V, 45 – 65Hz
- Current measuring unbalance supervision: 4 x 50mA – 5A, suitable for
CT x/1A and x/5A
- Connection with screw terminals
- Instrument casing for cutout 144 x 144mm, depth 49mm
- Protection class IP20 (casing), IP50 (Front)
further information, optional parts and supplies (PDF; 200kb) |
power-analyzers
Power Analyzer EMM-4
Multi-function power analyzer for acquisition and analysis of all parameters in 3-phase grids
zoom |
- 3-phase measurement with 3- or 4 wire connection
- Operation and parameter input with 4 keys
- User guidance with text menu
- Measurement data displayed on LCD display with backlight
- Harmonics measurement up to the 19. harmonic for voltage and current
- Connected to voltage transformers also suitable for higher voltages
- Interface RS232 on front
- Integration in networks possible via interface RS485 Modbus RTU or RS485 Profibus DP (optional)
- Data logger for measurement data and events via MMC storage card (optional)
- Impulse outputs for active and reactive energy (optional)
- Programmable alarms (optional)
- Measurement and supply voltage 400V +/-10%, 50/60Hz, other voltages on request
- Current measuring suitable for CT x/1A or x/5A
- Connection with pluggable screw terminals
- Instrument casing for cutout 144 x 144mm, depth 62
- Protection class IP20 (casing), IP50 (front)
further information, optional parts and supplies (PDF; 230kb) |
Power Analyzer EMM-5
Multi-function power analyzer for acquisition and analysis of all parameters in 3-phase grids
zoom |
- 3-phasige measurement with 3- or 4 wire connection
- Operation and parameter input with 4 keys
- User guidance with plain text menu
- Measurement data displayed on large LCD display with backlight
- Harmonics measurement up to the 63. harmonic for voltage and current
- In Verbindung mit Messwandlern auch für höhere Spannungen geeignet
- Connected to voltage transformers also suitable for higher voltages
- Integration in networks possible via interface RS485 Modbus RTU (optional)
- Flexible alarm system enables supervision of up to 32 measurement values
- Output relays (optional) can be programmed for external alarms
- Supply voltage 230V, 45-65Hz, other voltages on request
- Voltage measuring 50 – 530V, 45 – 65Hz
- Current measuring 50mA – 5A, suitable for CT x/1A und x/5A
- Connection with cage clamps
- Instrument casing for cutout 144 x 144mm, depth 49mm
- Protection class IP20 (casing), IP50 (front)
further information, optional parts and supplies(PDF; 360kb) |
SCADA-systems
Web Gateway miniSCADA
Configurable web gateway with integrated web server for direct Ethernet connection of devices with Modbus RTU interface
zoom |
- Monitor and control Modbus devices with standard web browser
- Configuration and design of web interface without special tools or HTML editors
- Send alarm messages via e-mail or SMS (external modem necessary)
- Data logging of selectable data points
- Can also be used as gateway for protools Modbus RTU/TCP
- Supply voltage 9 – 32V AC/DC
- Casing plastic grey 90 x 70 x 58mm, DIN rail mounting, IP20
further information, optional parts and supplies (PDF; 180kb)
You can see how miniSCADA operates together with BLR-CM and EMM5,
when you are using this link:
Demo miniSCADA
Access to miniSCADA is protected by password.
Please use this access data:
Zugandsdaten:
user: demo
password: demo |
|